interface Vlan77
ip address 172.16.77.254 255.255.255.0
ip helper-address 172.16.1.1
ip flow ingress
ip flow egress
ip pim sparse-mode
ip flow-export source Vlan9
ip flow-export version 9
ip flow-export destination 10.1.1.1 2056
Tag: 6500
6500 mls netflow
6509-1#sh mls netflow ip source 77.77.77.77
Displaying Netflow entries in Active Supervisor EARL in module 1/5
DstIP SrcIP Prot:SrcPort:DstPort Src i/f :AdjPtr
—————————————————————————–
Pkts Bytes Age LastSeen Attributes
—————————————————
10.77.77.101 77.77.77.77 udp :56969 :dns Vl31 :0×0
1 85 211 13:05:51 L2 – Dynamic
172.16.77.21 77.77.77.77 tcp :53416 :443 Vl31 :0×0
16 13730 8 13:09:15 L3 – Dynamic
10.77.77.101 77.77.77.77 udp :57666 :dns Vl31 :0×0
1 71 211 13:05:51 L2 – Dynamic
10.77.77.101 77.77.77.77 udp :62039 :dns Vl31 :0×0
1 69 8 13:09:14 L2 – Dynamic
172.16.77.52 77.77.77.77 tcp :53359 :443 Vl31 :0×0
1 46 291 13:04:31 L3 – Dynamic
10.77.77.101 77.77.77.77 udp :65402 :dns Vl31 :0×0
1 75 271 13:04:51 L2 – Dynamic
172.16.91.50 77.77.77.77 udp :57668 :389 Vl31 :0×0
1 196 211 13:05:51 L3 – Dynamic
172.16.9.52 77.77.77.77 tcp :49188 :5721 Vl31 :0×0
66 4026 998 13:09:14 L3 – Dynamic
33.33.25.205 77.77.77.77 tcp :53409 :443 Vl31 :0×0
13 3642 50 13:08:34 L3 – Dynamic
6500 TDR
6509#test cable-diagnostics tdr interface gi8/26
TDR test started on interface Gi8/26
A TDR test can take a few seconds to run on an interface
Use ‘show cable-diagnostics tdr’ to read the TDR results.
6509#show cab
6509#show cable-diagnostics td
6509#show cable-diagnostics tdr ?
interface Specify an interface for TDR
result
module Specify module for
TDR result
6509#show cable-diagnostics tdr interface gi8/26
TDR test last run on: October 13 10:02:06
Interface Speed Pair Cable
length Distance to fault
Channel Pair status
——— —– —- ——————- ——————- ——- ————
Gi8/26 auto 1-2
N/A
51 +/- 3 m Invalid
Open
3-4
N/A
48 +/- 3 m Invalid
Open
5-6
N/A
49 +/- 3 m Invalid
Open
7-8
N/A
52 +/- 3 m Invalid Open
6500 VSS – ISSU – notes
Make sure the old version is set in bootvar
Re: ISSU loadversion on VSS ? Make sure that the current image is
configured on the switch
boot system flash sup-bootdisk:s72033-ipbase-mz.122-33.SXI2a.bin
look at this post.
https://supportforums.cisco.com/message/606688
issu loadversion 1/5
sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI4a.bin 2/5
slavesup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI4a.bin
C6506VSS#issu runversion
This command will reload the Active unit. Proceed ?
[confirm]
C6506VSS# issu acceptversion
% Rollback timer stopped. Please issue the commitversion command.
C6506VSS#issu commitversion
Building configuration…
[OK]
%issu commitversion executed successfully
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SX/configuration/guide/issu_efsu.html#wp1042706
issu loadversion
sup-bootdisk:/newsys/s72033/base/s72033-advipservicesk9_wan-vm
2.copy
tftp sup-bootdisk:s72033-advipservicesk9-mz.122-33.SXI2a.bin
copy tftp slavesup-bootdisk:s72033-advipservicesk9-mz.122-33.SXI2a.bin
3.show version | inc image
show bootvar
show redundancy
show issu state detail
4. issu loadversion sup-bootdisk:s72033-advipservicesk9-mz.122-33.SXI2a.bin
5. show issu outage slot all
6 issu-runversion
7. issu acceptversion
8. issu commitversion
9. show redundancy
show issu state detail
At the end
redundancy force-switchover
to get on the right switch